Forum: Tools and Toys

Just ordered a Custom Armand Palacio Balisong for my EDC. They are handmade by Armand Palacio himself based in Balisong Batangas, Philippines. One of the only true FHM (Filipino Handmade) Balisong makers left. I should have it by early/mid December. 24cm (9.44") overall, latched. Pretty...

for those of you like me, who are not lucky enough to have a Walmart near them that carries ammo. I saw this thread on slick deals. http://slickdeals.net/forums/showthread.php?threadid=2136668 Prices are pretty decent.

Nearing the end of my run here in Phoenix at Universal Technical Institute in Avondale, AZ. I've learned quite a bit both in the automotive and in general life... Some aspects more than I wanted to, some not so much. But what I want to know... Techs. What are your most used tools in your chest...

Anyone have any hookups on riding gear, insurance, etc.? 09' Kawasaki ER-6n with 0 miles.

What websites do you guys go to for gun accessories or sales on guns? Im looking for sales or general information on what accessories i can get for the gun i just bought.

I think that might put me on some sort of homeland security carpentry watch list.

I picked this up a few days ago from 10 day gun jail. Its a Ruger KP89 9mm alloy frame, stainless slide. I was in the right place at the right time, only maybe half a box of rounds put through it, factory fired test casing and all the bits and Hogue grips.

New to me, glock 31 in .357 sig, under 100rds from previous owners. Picked it up tonight and tore it down and did a couple of minor changes to it. Replaced the trigger spring (slightly lighter) and the connector to a ghost 3.5lbs connector. Trigger cleaned up a lot, and pull is lighter. ...

I really want a 1911. I know there are "better/best" ones out there, but Im not looking to spend too much. I came across this: http://www.budsgunshop.com/catalog/product_info.php?products_id=32592 Anyone have experience with Springfield? Willing to take suggestions...Shoot em my way ...

Started getting parts to build this about a year ago, and just finished it. Yes, it took me forever -- I was very particular about it. Started with a Kaiser Defense stripped lower, an M4 stock with a Magpul pad, and a Colt lower parts kit. Got a DPMS 16" A2 upper, 5.56mm with 1/9 twist. ...

So, yesterday I picked up a Mossberg ATR 100 in .30-06. matte bluing with a black synthetic stock and Bushnell 3x9 scope. I wanted a nice bolt action to make a nice decent tack driver out of (for my skill level without spending $5K on a rifle). I don't compete, just shoot targets. Out of the box...

Looks like 2 new :tup: plus 2 old from COD 4.....:tdown: You'd think with the $310 million they grossed on opening day that they could afford to get developers to make 4 new maps. :P YouTube- MW2 Map Pack 1 LEAKED!!! Not a joke!!

YouTube- All-Time Favorite Commercial

I've been thinking about getting a new gun for awhile but I wasn't sure if I really felt safe having one like this around the house. I finally figured I should just bite the bullet and pick one up now that I live out in a rural area. With that said, here's my new framing nailer.

YouTube- Why Switzerland Has The Lowest Crime Rate In The World

Here are some Shots: We got to do a little shooting today, 9mm, .45 and 12 gauge... oh wait, and a surprise paintballing with a special guest:)

i own a snap on torque wrench that just so happen to break. does anyone know were i could take it to get replaced?

http://www.snapon.com/epiqpower/pdf/KEWNseries_npa.pdf Increase your work space ;)

DRILL PRESS: A tall upright machine useful for suddenly snatching flat metal bar stock out of your hands so that it smacks you in the chest and flings your beer across the room, denting the freshly-painted project which you had carefully set in the corner where nothing could get to it. WIRE...

Craftsman 12 Gallon Wet/Dry Vac

what are your feelings and thoughts?

Anyone have any experience with epoxy coatings for garage floors? I'm looking to see what's out there so I'd like to know what you've used and what was good and bad about it.

Its not a slider but its a great saw for someone planning to do a flooring or moulding project. Actually, for $100 bucks, its hard to go wrong. Amazon.com: Hitachi C10FCE2 10-Inch Compound Miter Saw: Home Improvement

I know there are some "cyclists" on here. im thinking about getting a road bike for the weekends and maybe riding to work a few days a week since gas is "supposed" to skyrocket this summer. does anyone have a suggestion of a semi decent beginner bike that wont totally break my budget? also any...

Put a Tadao board . . . 30 balls per second! YouTube - Paintball Test YouTube - Paintball Test2